Kingdom of Sardinia

The story of Italian pinfire guns and cartridges begins in the Kingdom of Sardinia with an order of 5000 Lefaucheux model 1854 revolvers. This first order was placed in 1859 and delivered in 1861 and these guns were referred to as the Corto model. They were pretty similar to the typical Lefaucheux model 1854 revolver except they had a 21% shorter barrel around 123mm long. At the time that these revolvers were ordered and delivered it is thought that the arsenals had not yet started producing their own pinfire cartridges yet so cartridges were likely imported from France or elsewhere as well.

The Kingdom of Italy

Shortly after these revolvers were ordered, the Kingdom of Italy was formed and a new order was made for another 12,000 revolvers.

During the American Civil War, Rolla, Missouri was a heavily garrisoned town that played a strategic role protecting the terminus of the Southwest Branch of the Pacific Railroad. This section of the railroad branched off the main Pacific Railroad of Missouri 40 miles southwest of St. Louis in Pacific City. It began construction in 1855 and the first train pulled into Rolla on December 22, 1860.

This article will take a look at a horizontal pinfire cartridge that has been unknown for quite some time. For awhile after I acquired it I could not figure out much about its history. But after discussing it with Fede Graziano we were able to get a little better understanding of it. This is the 14.5×48/49R Horizontal Pinfire cartridge and it was manufactured for or by Johann Jacob Peter of Stuttgart, Germany.

On 12 September 1859, a Norwegian military commission recommend contracting with Eugène Lefaucheux to acquire some of his model 1854 pinfire revolvers to begin updating their service handguns. In October 1859 they ordered 800 revolvers and 120,000 pinfire cartridges for the Norwegian Navy with a delivery date of summer 1860.

There are various sources that claim differing serial number ranges of this first order, but The Lefaucheux Family Archives has matched up original purchase orders and invoices to determine that they are around the LF14597 – LF15936 range. Some of this is detailed in the excellent book on the subject, La Production des Modeles d’Eugène Lefaucheux by Guillaume Van Mastrigt.

Norwegian Model 59

This first order of revolvers followed the below design as shown in this example from the Norwegian Armed Forces Museum where they have it labeled as an example of the Norwegian Navy Model 1859. It is thought that there are no special markings that specifically indicate which guns Lefaucheux made specifically went to fulfill this first order.

In 1983, the collective knowledge of pinfire firearms was greatly increased when Chris C. Curtis and Gene P. Smith wrote The Pinfire System, a new book detailing pinfire guns and ammunition from around the world.

The book featured images of guns, patents, advertising, cartridges and more. It was the first book that focused on this often neglected topic that played such an important role in the history of firearms. This book has been out of print for many years and often shows up on the collectors market for a couple hundred dollars. This book has more of a focus on the cartridges than his next book, with many pages dedicated to showing pinfire cartridges and even identifying headstamps.

Chris Curtis recently sent me the last of his pinfire cartridge box collection. Some of the boxes went to my collection and the rest are offered for sale here. I will notate the ones that appeared in his books.

A lot of people get Galand and Perrin cartridges confused, so we will take a look at these French thick rim cartridges over a few upcoming articles. The 9mm French thick rim cartridges are the most straight forward so we will start with them. Above all, the important take-away from this article is that, even though it is repeated in various articles and references, there is no such thing as a “Galand-Perrin” revolver. And these cartridges were never meant to be interchangeable nor were they ever designed to be used in the same guns.

What is a Perrin Cartridge?

A Perrin cartridge is an early centerfire cartridge invented by Louis Perrin in 1859. It was designed as an internally-primed cartridge which had a percussion cap resting in a metal anvil or frame inside the cartridge.

The pinfire system was one of the most important developments in the history of firearms. It mainstreamed the concept of fully-self-contained cartridges and breech-loading firearms.

Pinfire guns were made and used everywhere and were adopted at some point by nearly every major military in the world. Read through the following articles to learn about the relationship between the United States and pinfire.

This article will take a look at some of the smallest pinfire guns and cartridges. The 2mm pinfire cartridge showed up around 1880. This is when Société Française des Munitions began producing the variations shown in the following factory drawing.

These cartridges were made for tiny pinfire revolvers that looked like miniature versions of the normal pinfire revolvers. The following image is an example of one sold by Wayne Driskill Miniature Firearms.

When it comes to pinfire cartridges, everything is a variation. Though there are thousands and thousands of variations, in this article we will focus on the 80 that came from the White & Munhall reference collection.

Henry P. White & Burton D. Munhall ran a development engineering lab that was founded in 1936. They were acknowledged as the leading private laboratory engaged in small arms and ammunition research and development. The following sales brochure from the company gives a lot of detail on the work that they did.

This article will take a look at some leather cases for holding, storing and transporting pinfire cartridges. Since pinfire cartridges had to be handled with a little more care than other types of cartridges, some people purchased pouches such as these shown to make it safer and more convenient to carry the cartridges.

First up is a leather cartouchiere that holds twenty-four 7mm pinfire cartridges. It has a simple brass locking mechanism on the front that unlocks the case when you slide it and hold it down.

Here is a selection of factory drawings/blueprints for how Eley Bros made pinfire cartridges. These blueprints date to the early 1900s.

First up is the 5mm pinfire cartridge drawing. There is a lot going on here! It lists the dimensions for the bullet, the pin, the percussion cap and the case. They also give all of the dimensions in imperial units though these cartridges were always sold by their metric designation, “5mm.”

The bullet is described of being made of 98% lead and 2% antimony. The antimony was an additive used to harden the alloy. It was a hollow bullet with an overall diameter of .207 inches, or 5.258 millimeters. It had an overall height of .300 inches or 7.62 millimeters. The bullet weight is 18 grains and the powder charge is listed as “about 1.5 grains.”

This matches up closely with examples in my collection which have a bullet weight of 18.0 grains and a powder charge of 2 grains. The overall weight is 35.2 grains.

The brass case is listed to have a mixture of 70% copper and 30% zinc to make up the alloy they used. The case had an overall length of .450 inches or 11.43 millimeters. They give the exact specifications of where to put the hole for the brass pin and even what angle the pin should be placed in the cartridge to ensure the hammers get the best hit.

There have been many articles written about Jean Samuel Pauly and his contribution to the history of firearms development. One excellent source recently looks in detail at the patents by Pauly, Roux, Picherau and Lefaucheux. You can read about it here:

Priestel dives deep into the modifications by Pauly and the successors to Pauly’s company, but there are a few other improvements to the Pauly system by other prominent gunmakers of the day that are not addressed in this publication. A couple of these were mentioned in a French gun magazine’s article in the 1970s, but other than the brief mention there, there is nothing I could find published that goes into detail on the following improvements to the Pauly gun and cartridges.

So I gathered the patents, transcribed them and will detail the improvements here!

Jacques-Joseph Plomdeur | 1825-03-31

Jacques-Joseph Plomdeur was a well known gunmaker who had a business at 25 rue des Fossés-Montmartre and later at 5 bis, rue du Faubourg-Poissonnière. He was best known for his improvements to primers and percussion caps which he held a few patents on. In the 1830s he took out many advertisements for his improvements to guns and primers such as the following:

On 31 Mar 1825, Plomdeur took out a French patent for 5 years for an improvement on Pauly guns.

There are two main areas that he addresses. First is how the hammer is connected to the plate, passing all the way through, which allowed for considerable fouling throughout the inside.

James Erskine, a gunmaker and inventor from Newton Stewart, Scotland had a prolific career inventing and patenting many improvements to guns and cartridge loading machines. His patented cartridge filler was universally accepted and used by all of the great British gunmakers of the day!

Erskine was born on September 12, 1812, in Penninghame, Wigtownshire, Scotland, the son of Mary Watson and Thomas Erskine. He married Elizabeth Sinclair on December 4, 1854, in his hometown. They had eight children over 21 years. He died on November 20, 1891, in Newton Stewart, Wigtownshire, Scotland, having lived a long life of 79 years.

During most of those 79 years Erskine was active learning and then working in the gun trade. The IGC Historical Database indicates that Erskine began his apprenticeship at 14 years old, working as a gun finisher for Williams & Powell, or their predecessor, Edward Patrick in Liverpool.

Sometime after 1841 and before the 1851 Scotland Census, Erskine moved to Newton Stewart and began working for himself as a gun maker.

He displayed two guns at the 1851 Great Exhibition and was awarded a bronze metal.

On July 20, 1859 he delivered the following provisional specification to the British patent office for an update to the Lefaucheux-style pinfire shotgun:

August G. Genez was a French Gunsmith that began working in the gun-making industry at 13 years old in France. He died on June 17, 1897 and over the course of his career he had many successful ventures as well as challenging tragedies.

This article will take a look at A. G. Genez, the gunsmith in New York, New York, and follow his 50-year career in the gun industry. We will also take a look at his successors of his gun shop, Vincent Bissig and John P. Dannefelser.

When August Genez was 21 years old he immigrated to the United States from a port in Le Havre, France on a ship named Charles Thompson and arrived in New York, New York on April 10, 1854. The ship log of his emigration record states he was from Germany but his naturalization record, son’s wedding record, various ads of his, son’s various census records all state his birthplace was France.

The Genez name first shows up in the 1856/1857 issue of Trow’s New York City Directory where Genez August is listed as a gunsmith at 221 William. The same year the Wilson’s business directory of New-York City list him under the Gunsmiths section with his business at 221 William.